How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
What're your opinions about How to Install a Bathtub Yourself?
Setting up a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall to remove the old bathtub and place the new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. See to it you have certified yourself for the work as well as fit attempting it. Rather than employing a contractor to take over a halfway-completed task, it is much better to take into consideration employing one prior to you begin. Possibilities are you may require a professional plumber to make tube links.
This article will certainly help you set up a brand-new tub in your washroom if you have currently bought a brand-new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Getting ready for the Installment
Firstly, the supporting structure provided with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using both wooden boards under its feet, position the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the tub until the level reads degree.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leakages and tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub ought to wait till the bathtub has actually been made use of a minimum of when as this will resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog post about How to Install a Bathtub Yourself while doing a lookup on the internet. Make sure you set aside a second to distribute this article if you enjoyed it. Thank you so much for your time invested reading it.
Hire A Pro Report this page